What FD30 fire doors in Farnworth should include
Our FD30 fire doors service covers Farnworth and the wider Greater Manchester area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Farnworth has a broad mix of buildings, including family homes after loft conversions, care homes and small offices, and the same fire door principles apply to all of them.
In Farnworth, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. For a mixed portfolio in Farnworth, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side.
Where are FD30 doors used?
FD30 is the rating most buildings rely on. You will find it on flat entrance doors, doors onto escape corridors and stairs in houses in multiple occupation, kitchen doors in HMOs, and most internal doors on escape routes in offices, schools, surgeries and shops. Where smoke control matters too, the door is specified as FD30S (E30Sa), which adds a smoke seal and a tighter threshold.
The rating your building needs comes from its fire strategy or fire risk assessment, not from the door supplier. If you are unsure whether a door should be FD30 or FD60, we check the drawings, the risk assessment and what is installed now before we price anything. Our FD30 vs FD60 guide explains the difference.
What you get:
- Photo record, product data and certificate references at handover
- Overhead closer set to close and latch
- Fire-tested hinges, latch or lock and intumescent pads
- Survey of the opening, frame and existing ironmongery
The regulations behind fire doors in Farnworth
In Farnworth, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Farnworth building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Who needs FD30 fire doors in Farnworth?
The need for FD30 fire doors usually arises in offices or care homes, and sometimes schools. Each has its own pressures, such as residents at home or a building that must stay open, so we plan the sequence of work in Farnworth to keep escape routes protected throughout.
What happens after you enquire
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Farnworth?
As a guide, budget £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. The figure for your Farnworth building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Farnworth and neighbouring towns
Nearby towns we cover include Walkden, Bolton and Radcliffe. Distance from Farnworth does not change our guide prices, and the survey and quote are free.
Questions
Is Farnworth within your coverage area?
It is. We cover Farnworth in Greater Manchester and neighbouring towns such as Walkden. There is no charge for the survey.
Can you work from an existing inspection report for my Farnworth building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.