FD30 fire doors in Golborne, done to the evidence
Looking for FD30 fire doors in Golborne? We supply and fit certified fire doors and components across Golborne and the wider Merseyside area, working from a free survey and a fixed written quote.
In and around Golborne, fire door work covers everything from small blocks of flats to family homes after loft conversions. We plan each job around the people who use the building.
Each FD30 leaf we supply for Golborne is sized for the opening, rather than trimmed beyond what its certification allows. In Golborne, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
On a typical job that means:
- Certified FD30 or FD30S leaf, or full doorset
- Overhead closer set to close and latch
- Survey of the opening, frame and existing ironmongery
- Fire-tested hinges, latch or lock and intumescent pads
Fire door law for Golborne properties
Fire doors in Golborne fall under English rules. New and replacement doors are covered by the Building Regulations 2010 and Approved Document B. In workplaces and the common parts of blocks, the Regulatory Reform (Fire Safety) Order 2005, as clarified by the Fire Safety Act 2021, puts the duty on the responsible person to keep fire doors suitable and maintained.
For residential buildings in Golborne above 11 metres, regulation 10 of the Fire Safety (England) Regulations 2022 adds checks: communal fire doors at least every three months and best-endeavours checks of flat entrance doors at least every twelve months. Higher-risk buildings of at least 18 metres or seven storeys also come under the Building Safety Act 2022, where works may need approval from the Building Safety Regulator.
Who needs FD30 fire doors in Golborne?
Landlords, managing agents, facilities teams and homeowners in Golborne can all commission FD30 fire doors from us. The usual settings are offices and schools, though single doors for care homes are just as welcome.
From enquiry to handover in Golborne
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Golborne
Guide pricing for FD30 fire doors: £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. Volume work across several doors in one Golborne building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Around Golborne
We also cover towns near Golborne, including Newton-le-Willows (3.0 km away), Ashton-in-Makerfield and Leigh. If your building is in WA12 or a neighbouring district, the service and pricing are the same.
Questions from Golborne
Do you cover WA12 and nearby postcodes?
Yes. We cover Golborne including WA12, and nearby towns such as Newton-le-Willows and Ashton-in-Makerfield. The survey and written quote are free.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.