FD30 fire doors in Bebington, done to the evidence
If you need FD30 fire doors in Bebington, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
Fire doors in Bebington protect escape routes in care homes, HMOs and family homes after loft conversions alike. We adapt the programme to the building and its occupants, never the standard of the installation.
Each FD30 leaf we supply for Bebington is sized for the opening, rather than trimmed beyond what its certification allows. In Bebington, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
As standard, the work covers:
- Survey of the opening, frame and existing ironmongery
- Certified FD30 or FD30S leaf, or full doorset
- Frame-to-wall gap sealed with an evidenced material
- Intumescent strips and smoke seals to the certification
Fire door law for Bebington properties
The rules that apply to fire doors in Bebington are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Bebington block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Which buildings in Bebington need FD30 fire doors?
From care homes to schools, the requirement for FD30 fire doors in Bebington comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
The steps on a Bebington installation
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Prices for FD30 fire doors in Bebington
Guide pricing for FD30 fire doors: £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. Volume work across several doors in one Bebington building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Bebington and neighbouring towns
Nearby towns we cover include Birkenhead, Heswall and Liverpool. Distance from Bebington does not change our guide prices, and the survey and quote are free.
Questions
Is Bebington within your coverage area?
It is. We cover Bebington in Merseyside and neighbouring towns such as Birkenhead. There is no charge for the survey.
Can you work from an existing inspection report for my Bebington building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.