FD30 fire doors in Bootle, done to the evidence
If you need FD30 fire doors in Bootle, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
In and around Bootle, fire door work covers everything from family homes after loft conversions to low-rise blocks of flats. We plan each job around the people who use the building.
In Bootle, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. Each FD30 leaf we supply for Bootle is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
Each installation includes:
- Survey of the opening, frame and existing ironmongery
- Frame-to-wall gap sealed with an evidenced material
- Certified FD30 or FD30S leaf, or full doorset
- Overhead closer set to close and latch
Fire door law for Bootle properties
In Bootle, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Bootle building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Who needs FD30 fire doors in Bootle?
From shops to offices, the requirement for FD30 fire doors in Bootle comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
Our process in Bootle
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Bootle?
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Bootle and neighbouring towns
We also cover towns near Bootle, including Litherland (1.3 km away), Wallasey and Liverpool. If your building is in L21 or a neighbouring district, the service and pricing are the same.
Questions
Do you work in Bootle?
Yes, we take on FD30 fire doors in Bootle and the surrounding area, including Litherland and Wallasey. Send your postcode and a few details and we'll come back with survey dates.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.