FD60 fire doors: our service in Coventry
When you book FD60 fire doors in Coventry, the aim is simple: doors that close, latch and seal as tested, with records that prove it.
Buildings in and around Coventry range from care homes to clinics and shared houses. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
FD60 openings in Coventry buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. Before ordering FD60 doors for a Coventry building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer.
When does a building need FD60 rather than FD30?
FD60 doors appear where the fire strategy asks a wall to resist fire for an hour: stair cores and lobbies in taller buildings, plant and boiler rooms, some service risers, refuse stores and compartment walls between different uses. The rating follows the wall. Fitting an FD30 door in a 60-minute wall leaves a weak point, and fitting FD60 everywhere wastes money and makes doors harder to open.
We work from your fire strategy, the building's drawings or the fire risk assessment. Where these disagree with what is on site, we flag it before ordering.
As standard, the work covers:
- Check of the fire strategy rating for each opening
- Intumescent and smoke seals as specified
- Load-rated hinges and correctly powered closer
- Frame fixing and structural gap sealing recorded with photos
The regulations behind fire doors in Coventry
The rules that apply to fire doors in Coventry are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Coventry block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Who needs FD60 fire doors in Coventry?
Typical settings for FD60 fire doors include plant and boiler rooms, refuse stores and mixed-use commercial buildings. In Coventry, as anywhere, the duty holder varies: a responsible person for a workplace, a landlord or managing agent for a block or HMO, or a homeowner after building work. We adjust access, timing and paperwork to suit whoever commissions the work.
What happens after you enquire
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
What does FD60 fire doors cost in Coventry?
If you need a budget figure first, the guide for FD60 fire doors is £850–£1,800 per FD60 doorset supplied and fitted, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Coventry
Coventry is about 27.6 km from Birmingham, and we cover both, along with nearby Kenilworth and Bedworth. Send us your postcode and we'll confirm survey dates.
Questions from Coventry
Do you work in Coventry?
Yes, we take on FD60 fire doors in Coventry and the surrounding area, including Kenilworth and Bedworth. Send your postcode and a few details and we'll come back with survey dates.
What happens on a survey in Coventry?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.
Do FD60 doors need smoke seals?
If the fire strategy asks for smoke control, yes: the door will be specified as FD60S or E60Sa with smoke seals. Many plant room doors are FD60 without a smoke requirement.