What FD30 fire doors in Pontefract should include
For property owners, landlords and managing agents in Pontefract, we offer FD30 fire doors with one team for the survey, the product and the installation.
Around Pontefract, schools, care homes and small offices all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
In Pontefract, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. Each FD30 leaf we supply for Pontefract is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Certified FD30 or FD30S leaf, or full doorset
- Intumescent strips and smoke seals to the certification
- Overhead closer set to close and latch
- Photo record, product data and certificate references at handover
What the rules say for Pontefract
Fire doors in Pontefract fall under English rules. New and replacement doors are covered by the Building Regulations 2010 and Approved Document B. In workplaces and the common parts of blocks, the Regulatory Reform (Fire Safety) Order 2005, as clarified by the Fire Safety Act 2021, puts the duty on the responsible person to keep fire doors suitable and maintained.
For residential buildings in Pontefract above 11 metres, regulation 10 of the Fire Safety (England) Regulations 2022 adds checks: communal fire doors at least every three months and best-endeavours checks of flat entrance doors at least every twelve months. Higher-risk buildings of at least 18 metres or seven storeys also come under the Building Safety Act 2022, where works may need approval from the Building Safety Regulator.
Where FD30 fire doors fit in Pontefract
Typical settings for FD30 fire doors include shops, HMOs and schools. In Pontefract, as anywhere, the duty holder varies: a responsible person for a workplace, a landlord or managing agent for a block or HMO, or a homeowner after building work. We adjust access, timing and paperwork to suit whoever commissions the work.
How a Pontefract job runs
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Pontefract
Guide pricing for FD30 fire doors: £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. Volume work across several doors in one Pontefract building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Nearby areas we cover from Pontefract
We also cover towns near Pontefract, including Castleford (5.1 km away), Wakefield and Lofthouse. If your building is in WF8 or a neighbouring district, the service and pricing are the same.
Questions from Pontefract
Is Pontefract within your coverage area?
It is. We cover Pontefract in West Yorkshire and neighbouring towns such as Castleford. There is no charge for the survey.
What happens on a survey in Pontefract?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.