FD30 fire doors for Ilkeston buildings
From the DE7 postcode district outwards, we take on FD30 fire doors across Ilkeston for homes, blocks and workplaces.
Buildings in and around Ilkeston range from care homes to houses with integral garages and schools. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
For a mixed portfolio in Ilkeston, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side. Each FD30 leaf we supply for Ilkeston is sized for the opening, rather than trimmed beyond what its certification allows.
Where are FD30 doors used?
FD30 is the rating most buildings rely on. You will find it on flat entrance doors, doors onto escape corridors and stairs in houses in multiple occupation, kitchen doors in HMOs, and most internal doors on escape routes in offices, schools, surgeries and shops. Where smoke control matters too, the door is specified as FD30S (E30Sa), which adds a smoke seal and a tighter threshold.
The rating your building needs comes from its fire strategy or fire risk assessment, not from the door supplier. If you are unsure whether a door should be FD30 or FD60, we check the drawings, the risk assessment and what is installed now before we price anything. Our FD30 vs FD60 guide explains the difference.
On a typical job that means:
- Intumescent strips and smoke seals to the certification
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
- Frame-to-wall gap sealed with an evidenced material
Rules and responsibilities in Ilkeston
In Ilkeston, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Ilkeston building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Buildings and duty holders in Ilkeston
You are most likely to need FD30 fire doors if you look after blocks of flats, care homes or schools. Whatever the building in Ilkeston, we survey each opening and tell you which doors need work and which do not.
How a Ilkeston job runs
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Ilkeston
Budget around £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. Our guide prices are the same in Ilkeston as elsewhere; what changes the cost is the doors themselves. Use our guide-price tool for a quick estimate.
Nearby areas we cover from Ilkeston
Neighbouring towns such as Heanor, Long Eaton, Ripley and Hucknall are covered too, so clients with several buildings can use one installer and one evidence format.
Common questions
Is Ilkeston within your coverage area?
It is. We cover Ilkeston in Derbyshire and neighbouring towns such as Heanor. There is no charge for the survey.
What happens on a survey in Ilkeston?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.