Fire door ironmongery for Walton-on-Thames buildings
We provide fire door ironmongery in Walton-on-Thames (KT12 and the surrounding postcodes), from the first survey through to a documented handover.
Around Walton-on-Thames, small blocks of flats, houses with integral garages and schools all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
We supply ironmongery for Walton-on-Thames fire doors that matches each door's test evidence. Signage for fire doors in Walton-on-Thames buildings is fitted as part of the job, not as an afterthought.
Why hardware choice matters
Fire doors are tested with particular hardware. Hinges hold the door in place as it heats up; locks and latches keep it shut against fire pressure; their holes are protected with intumescent linings. Swapping in a cheaper hinge, a larger lock body or a lever on a spindle that melts can change how the door behaves. Hinges for fire doors are commonly grade 13 to BS EN 1935.
What you get:
- Intumescent pads and lock linings
- Lever handles, pull handles and push plates
- Fire-rated hinges, commonly grade 13
- Locks and latches covered by the evidence
What the rules say for Walton-on-Thames
Fire doors in Walton-on-Thames fall under English rules. New and replacement doors are covered by the Building Regulations 2010 and Approved Document B. In workplaces and the common parts of blocks, the Regulatory Reform (Fire Safety) Order 2005, as clarified by the Fire Safety Act 2021, puts the duty on the responsible person to keep fire doors suitable and maintained.
For residential buildings in Walton-on-Thames above 11 metres, regulation 10 of the Fire Safety (England) Regulations 2022 adds checks: communal fire doors at least every three months and best-endeavours checks of flat entrance doors at least every twelve months. Higher-risk buildings of at least 18 metres or seven storeys also come under the Building Safety Act 2022, where works may need approval from the Building Safety Regulator.
Which buildings in Walton-on-Thames need fire door ironmongery?
From offices to schools, the requirement for fire door ironmongery in Walton-on-Thames comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
From enquiry to handover in Walton-on-Thames
- Identify the door's certification and hardware schedule
- List items that need replacing
- Supply matching hardware
- Fit with correct pads and linings
- Check operation, closing and latching
- Record what was fitted
Guide prices in Walton-on-Thames
If you need a budget figure first, the guide for fire door ironmongery is from £40 for minor items to £350 for a full hardware set per door, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Walton-on-Thames and neighbouring towns
Walton-on-Thames is about 12.6 km from Woking, and we cover both, along with nearby Sunbury-on-Thames and Esher. Send us your postcode and we'll confirm survey dates.
Questions
Do you work in Walton-on-Thames?
Yes, we take on fire door ironmongery in Walton-on-Thames and the surrounding area, including Sunbury-on-Thames and Esher. Send your postcode and a few details and we'll come back with survey dates.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
Do fire doors need signs?
Most fire doors in non-domestic buildings and common parts should carry signage showing whether they are to be kept shut, kept locked or are automatic.
Can I fit a new lock to a fire door?
Only one that is covered by the door's test evidence, fitted with the correct intumescent protection. A larger lock body or new holes can compromise the door.