FD60 fire doors in Camberley: what's involved
If you need FD60 fire doors in Camberley, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
Camberley has a broad mix of buildings, including houses with integral garages, schools and small offices, and the same fire door principles apply to all of them.
FD60 openings in Camberley buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. For FD60 work in Camberley we generally fit certified doorsets, so frame and leaf share the same test evidence.
When does a building need FD60 rather than FD30?
FD60 doors appear where the fire strategy asks a wall to resist fire for an hour: stair cores and lobbies in taller buildings, plant and boiler rooms, some service risers, refuse stores and compartment walls between different uses. The rating follows the wall. Fitting an FD30 door in a 60-minute wall leaves a weak point, and fitting FD60 everywhere wastes money and makes doors harder to open.
We work from your fire strategy, the building's drawings or the fire risk assessment. Where these disagree with what is on site, we flag it before ordering.
Each installation includes:
- Frame fixing and structural gap sealing recorded with photos
- Certified FD60 doorset or leaf with matching evidence
- Check of the fire strategy rating for each opening
- Load-rated hinges and correctly powered closer
Rules and responsibilities in Camberley
The rules that apply to fire doors in Camberley are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Camberley block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Which buildings in Camberley need FD60 fire doors?
The need for FD60 fire doors usually arises in stair cores in taller blocks or refuse stores, and sometimes plant and boiler rooms. Each has its own pressures, such as residents at home or a building that must stay open, so we plan the sequence of work in Camberley to keep escape routes protected throughout.
How a Camberley job runs
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Budgeting for FD60 fire doors in Camberley
As a guide, budget £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. The figure for your Camberley building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Nearby areas we cover from Camberley
Camberley is about 12.9 km from Woking, and we cover both, along with nearby Sandhurst and Farnborough. Send us your postcode and we'll confirm survey dates.
Questions from Camberley
Is Camberley within your coverage area?
It is. We cover Camberley in Surrey and neighbouring towns such as Sandhurst. There is no charge for the survey.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.