FD30 fire doors in Denton: what's involved
If you need FD30 fire doors in Denton, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
In and around Denton, fire door work covers everything from schools to small blocks of flats. We plan each job around the people who use the building.
For a mixed portfolio in Denton, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side. Each FD30 leaf we supply for Denton is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
As standard, the work covers:
- Certified FD30 or FD30S leaf, or full doorset
- Fire-tested hinges, latch or lock and intumescent pads
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
The regulations behind fire doors in Denton
In Denton, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Denton building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD30 fire doors fit in Denton
From HMOs to blocks of flats, the requirement for FD30 fire doors in Denton comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
The steps on a Denton installation
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Budgeting for FD30 fire doors in Denton
Guide pricing for FD30 fire doors: £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. Volume work across several doors in one Denton building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Covering Denton and nearby
Nearby towns we cover include Hyde, Dukinfield and Droylsden. Distance from Denton does not change our guide prices, and the survey and quote are free.
Questions
Do you work in Denton?
Yes, we take on FD30 fire doors in Denton and the surrounding area, including Hyde and Dukinfield. Send your postcode and a few details and we'll come back with survey dates.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.