Intumescent strips and smoke seals for Barrow-in-Furness buildings
Our intumescent strips and smoke seals service in Barrow-in-Furness is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Buildings in and around Barrow-in-Furness range from houses with integral garages to schools and low-rise blocks of flats. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
Painted and missing seals are among the most common fire door defects nationally; in Barrow-in-Furness we replace them with the type and size the certification specifies. Seal replacement in Barrow-in-Furness can be combined with any other remedials on the same inspection report.
Getting the specification right
The door's certification states the type, size and position of strips and seals: in the frame or the leaf edge, single or double, and whether a combined intumescent and smoke seal is used. Replacements must match. Swapping in a generic strip from a hardware shop can undermine the door's performance.
Each installation includes:
- Check of gaps and closing after fitting
- Intumescent pads to hinges and locks
- Removal of damaged or painted seals
- Identification of the specified seals
What the rules say for Barrow-in-Furness
The rules that apply to fire doors in Barrow-in-Furness are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Barrow-in-Furness block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Which buildings in Barrow-in-Furness need intumescent strips and smoke seals?
The need for intumescent strips and smoke seals usually arises in blocks of flats or care homes, and sometimes schools. Each has its own pressures, such as residents at home or a building that must stay open, so we plan the sequence of work in Barrow-in-Furness to keep escape routes protected throughout.
The steps on a Barrow-in-Furness installation
- Identify door certification and seal specification
- Remove failed seals and clean the grooves
- Fit new strips and seals to the specified positions
- Fit missing pads and lock linings
- Check the door closes and latches against the new seals
- Record the products fitted
Guide prices in Barrow-in-Furness
As a guide, budget £45–£110 per door to supply and fit strips and seals, ex VAT for intumescent strips and smoke seals. The figure for your Barrow-in-Furness building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Around Barrow-in-Furness
Neighbouring towns such as Morecambe, Fleetwood, Lancaster and Thornton-Cleveleys are covered too, so clients with several buildings can use one installer and one evidence format.
Common questions
Is Barrow-in-Furness within your coverage area?
It is. We cover Barrow-in-Furness in Cumbria and neighbouring towns such as Morecambe. There is no charge for the survey.
Can you work from an existing inspection report for my Barrow-in-Furness building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Can smoke seals be painted?
No. Paint stops brush and blade seals working. If seals have been painted, they should be replaced.
Can I just add intumescent strips to an ordinary door?
No. Strips do not turn an ordinary door into a fire door. They only work as part of a door that was tested and certified with them.