Certified fire doorsets for Shrewsbury buildings
Our certified fire doorsets service in Shrewsbury is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Buildings in and around Shrewsbury range from HMOs to houses with integral garages and industrial estates. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
Doorsets suit refurbishment programmes in Shrewsbury, where several openings can be measured, ordered and fitted in one planned sequence. Pre-hung doorsets keep disruption down in occupied buildings in Shrewsbury, with less cutting and fewer return visits.
Why choose a doorset over a door leaf?
A fire door's rating belongs to the assembly that was tested, not to the leaf on its own. When a certified leaf is hung in an old frame with mismatched hinges and seals, nobody can say with confidence how it will perform. A doorset arrives with the frame, gaps and ironmongery already matched, so the installer's job is to fix it correctly into the opening and seal it to the structure.
Doorsets also cut time on site, which matters in occupied buildings: less cutting, less dust and fewer return visits.
What you get:
- Frame fixing and frame-to-wall gap sealing
- Pre-hung, pre-machined doorsets where available
- Certificate references and photo record per opening
- Doorset selection to rating, size and use
Which fire door rules apply in Shrewsbury?
The rules that apply to fire doors in Shrewsbury are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Shrewsbury block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Which buildings in Shrewsbury need certified fire doorsets?
You are most likely to need certified fire doorsets if you look after refurbishment programmes, schools and offices or blocks of flats. Whatever the building in Shrewsbury, we survey each opening and tell you which doors need work and which do not.
Our process in Shrewsbury
- Survey and measure every structural opening
- Specify doorsets by rating, size, hand, finish and hardware
- Prepare openings and remove existing doors and linings
- Fix and seal the frames to the structure
- Hang, adjust and test each leaf and closer
- Fit architraves, make good and hand over evidence
What does certified fire doorsets cost in Shrewsbury?
As a guide, budget £650–£1,300 for an FD30 doorset and £850–£1,800 for FD60, supplied and fitted, ex VAT for certified fire doorsets. The figure for your Shrewsbury building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Around Shrewsbury
Nearby towns we cover include Wellington, Telford and Rhosllannerchrugog. Distance from Shrewsbury does not change our guide prices, and the survey and quote are free.
Common questions
Is Shrewsbury within your coverage area?
It is. We cover Shrewsbury in Shropshire and neighbouring towns such as Wellington. There is no charge for the survey.
Can you work from an existing inspection report for my Shrewsbury building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Are doorsets more expensive than a leaf?
The product costs more, but the labour is often lower and the result is better evidenced. Where a frame would need replacing anyway, a doorset is usually the better value.
Can a doorset be fitted into an existing opening?
Usually, yes. Doorsets are made to fit the structural opening once the old frame is removed. We measure the opening on the survey so the doorset is made to the right size and the gaps to the wall stay within what the evidence allows.