FD60 fire doors in Chichester, done to the evidence
Our FD60 fire doors service covers Chichester and the wider West Sussex area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Around Chichester, small blocks of flats, small offices and houses with integral garages all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
FD60 openings in Chichester buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. Before ordering FD60 doors for a Chichester building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer.
What do you hand over at the end?
For every FD60 opening we record the product and certificate reference, the gap measurements, the hinge and closer specification, how the frame was fixed and what was used to seal the frame-to-structure gap, with photographs before the architraves go on. That record is what your fire risk assessor or building control officer will ask for.
On a typical job that means:
- Certified FD60 doorset or leaf with matching evidence
- Check of the fire strategy rating for each opening
- Load-rated hinges and correctly powered closer
- Frame fixing and structural gap sealing recorded with photos
Which fire door rules apply in Chichester?
The rules that apply to fire doors in Chichester are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Chichester block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Buildings and duty holders in Chichester
You are most likely to need FD60 fire doors if you look after mixed-use commercial buildings, plant and boiler rooms or refuse stores. Whatever the building in Chichester, we survey each opening and tell you which doors need work and which do not.
How a Chichester job runs
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Budgeting for FD60 fire doors in Chichester
As a guide, budget £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. The figure for your Chichester building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Around Chichester
Chichester is about 51.9 km from Crawley, and we cover both, along with nearby Bognor Regis and Havant. Send us your postcode and we'll confirm survey dates.
Questions from Chichester
Do you work in Chichester?
Yes, we take on FD60 fire doors in Chichester and the surrounding area, including Bognor Regis and Havant. Send your postcode and a few details and we'll come back with survey dates.
How quickly can you survey in Chichester?
It depends on the number of doors and access, but we offer survey dates as soon as we reply to your enquiry. If an inspection has found urgent safety issues, tell us and we'll prioritise.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.
Do FD60 doors need smoke seals?
If the fire strategy asks for smoke control, yes: the door will be specified as FD60S or E60Sa with smoke seals. Many plant room doors are FD60 without a smoke requirement.