FD60 fire doors: our service in East Grinstead
We provide FD60 fire doors in East Grinstead (RH19 and the surrounding postcodes), from the first survey through to a documented handover.
Fire doors in East Grinstead protect escape routes in schools, houses with integral garages and care homes alike. We adapt the programme to the building and its occupants, never the standard of the installation.
FD60 openings in East Grinstead buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. Before ordering FD60 doors for a East Grinstead building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer.
What do you hand over at the end?
For every FD60 opening we record the product and certificate reference, the gap measurements, the hinge and closer specification, how the frame was fixed and what was used to seal the frame-to-structure gap, with photographs before the architraves go on. That record is what your fire risk assessor or building control officer will ask for.
Each installation includes:
- Load-rated hinges and correctly powered closer
- Check of the fire strategy rating for each opening
- Intumescent and smoke seals as specified
- Frame fixing and structural gap sealing recorded with photos
Rules and responsibilities in East Grinstead
In East Grinstead, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your East Grinstead building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD60 fire doors fit in East Grinstead
Landlords, managing agents, facilities teams and homeowners in East Grinstead can all commission FD60 fire doors from us. The usual settings are stair cores in taller blocks and refuse stores, though single doors for plant and boiler rooms are just as welcome.
What happens after you enquire
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
What does FD60 fire doors cost in East Grinstead?
Budget around £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. Our guide prices are the same in East Grinstead as elsewhere; what changes the cost is the doors themselves. Use our guide-price tool for a quick estimate.
Nearby areas we cover from East Grinstead
We also cover towns near East Grinstead, including Horley (12.1 km away), Crawley and Crowborough. If your building is in RH19 or a neighbouring district, the service and pricing are the same.
Questions from East Grinstead
Do you work in East Grinstead?
Yes, we take on FD60 fire doors in East Grinstead and the surrounding area, including Horley and Crawley. Send your postcode and a few details and we'll come back with survey dates.
Can you work from an existing inspection report for my East Grinstead building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.

