FD60 fire doors in Newburn, done to the evidence
Our FD60 fire doors service covers Newburn and the wider Tyne and Wear area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Around Newburn, small blocks of flats, schools and family homes after loft conversions all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
FD60 openings in Newburn buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. For FD60 work in Newburn we generally fit certified doorsets, so frame and leaf share the same test evidence.
When does a building need FD60 rather than FD30?
FD60 doors appear where the fire strategy asks a wall to resist fire for an hour: stair cores and lobbies in taller buildings, plant and boiler rooms, some service risers, refuse stores and compartment walls between different uses. The rating follows the wall. Fitting an FD30 door in a 60-minute wall leaves a weak point, and fitting FD60 everywhere wastes money and makes doors harder to open.
We work from your fire strategy, the building's drawings or the fire risk assessment. Where these disagree with what is on site, we flag it before ordering.
What you get:
- Certified FD60 doorset or leaf with matching evidence
- Intumescent and smoke seals as specified
- Load-rated hinges and correctly powered closer
- Frame fixing and structural gap sealing recorded with photos
What the rules say for Newburn
The rules that apply to fire doors in Newburn are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Newburn block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Buildings and duty holders in Newburn
You are most likely to need FD60 fire doors if you look after stair cores in taller blocks, plant and boiler rooms or refuse stores. Whatever the building in Newburn, we survey each opening and tell you which doors need work and which do not.
From enquiry to handover in Newburn
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Budgeting for FD60 fire doors in Newburn
Budget around £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. Our guide prices are the same in Newburn as elsewhere; what changes the cost is the doors themselves. Use our guide-price tool for a quick estimate.
Around Newburn
Nearby towns we cover include Gosforth, Newcastle upon Tyne and Gateshead. Distance from Newburn does not change our guide prices, and the survey and quote are free.
Questions from Newburn
Do you cover NE15 and nearby postcodes?
Yes. We cover Newburn including NE15, and nearby towns such as Gosforth and Newcastle upon Tyne. The survey and written quote are free.
Can you work from an existing inspection report for my Newburn building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Are FD60 doors harder to open?
They are heavier, so the closer has to be chosen and adjusted with care. A well-set closer will still close and latch the door while keeping the opening force reasonable for the people who use it.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.