Getting FD30 fire doors right in Arnold
From the NG5 postcode district outwards, we take on FD30 fire doors across Arnold for homes, blocks and workplaces.
Buildings in and around Arnold range from houses with integral garages to light industrial buildings and small blocks of flats. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
Each FD30 leaf we supply for Arnold is sized for the opening, rather than trimmed beyond what its certification allows. In Arnold, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes.
Leaf only or a full doorset?
If the existing frame is sound, correctly sized, securely fixed and compatible with the new leaf's certification, a new FD30 leaf can be hung in it. Many frames do not pass that test: old softwood linings, frames that have been cut about for previous doors, or frames with no evidence of how they were fixed. In those cases a certified doorset (leaf, frame and ironmongery tested together) is the cleaner answer and usually the quicker one on site.
We tell you which route each opening needs on the survey, door by door, and why.
Each installation includes:
- Intumescent strips and smoke seals to the certification
- Fire-tested hinges, latch or lock and intumescent pads
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
Which fire door rules apply in Arnold?
The rules that apply to fire doors in Arnold are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Arnold block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Buildings and duty holders in Arnold
From shops to schools, the requirement for FD30 fire doors in Arnold comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
The steps on a Arnold installation
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Arnold
As a guide, budget £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. The figure for your Arnold building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Around Arnold
Arnold is about 5.3 km from Nottingham, and we cover both, along with nearby Hucknall and West Bridgford. Send us your postcode and we'll confirm survey dates.
Common questions
Is Arnold within your coverage area?
It is. We cover Arnold in Nottinghamshire and neighbouring towns such as Nottingham. There is no charge for the survey.
What happens on a survey in Arnold?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.