Getting FD30 fire doors right in Stamford
Our FD30 fire doors service covers Stamford and the wider Lincolnshire area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Buildings in and around Stamford range from small offices to schools and care homes. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
For a mixed portfolio in Stamford, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side. Each FD30 leaf we supply for Stamford is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Frame-to-wall gap sealed with an evidenced material
- Photo record, product data and certificate references at handover
- Fire-tested hinges, latch or lock and intumescent pads
- Overhead closer set to close and latch
What the rules say for Stamford
In Stamford, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Stamford building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD30 fire doors fit in Stamford
Typical settings for FD30 fire doors include shops, offices and blocks of flats. In Stamford, as anywhere, the duty holder varies: a responsible person for a workplace, a landlord or managing agent for a block or HMO, or a homeowner after building work. We adjust access, timing and paperwork to suit whoever commissions the work.
What happens after you enquire
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Stamford?
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Stamford
Nearby towns we cover include Peterborough, Corby and Spalding. Distance from Stamford does not change our guide prices, and the survey and quote are free.
Common questions
Do you cover PE9 and nearby postcodes?
Yes. We cover Stamford including PE9, and nearby towns such as Peterborough and Corby. The survey and written quote are free.
How quickly can you survey in Stamford?
It depends on the number of doors and access, but we offer survey dates as soon as we reply to your enquiry. If an inspection has found urgent safety issues, tell us and we'll prioritise.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.