What FD30 fire doors in Cleethorpes should include
If you need FD30 fire doors in Cleethorpes, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
Cleethorpes has a broad mix of buildings, including houses with integral garages, small blocks of flats and light industrial buildings, and the same fire door principles apply to all of them.
In Cleethorpes, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. Each FD30 leaf we supply for Cleethorpes is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
As standard, the work covers:
- Survey of the opening, frame and existing ironmongery
- Frame-to-wall gap sealed with an evidenced material
- Photo record, product data and certificate references at handover
- Certified FD30 or FD30S leaf, or full doorset
Which fire door rules apply in Cleethorpes?
The rules that apply to fire doors in Cleethorpes are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Cleethorpes block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Which buildings in Cleethorpes need FD30 fire doors?
From blocks of flats to shops, the requirement for FD30 fire doors in Cleethorpes comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
What happens after you enquire
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Cleethorpes
Budget around £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. Our guide prices are the same in Cleethorpes as elsewhere; what changes the cost is the doors themselves. Use our guide-price tool for a quick estimate.
Nearby areas we cover from Cleethorpes
We also cover towns near Cleethorpes, including Grimsby (2.9 km away), Kingston upon Hull and Beverley. If your building is in DN35 or a neighbouring district, the service and pricing are the same.
Questions
Do you cover DN35 and nearby postcodes?
Yes. We cover Cleethorpes including DN35, and nearby towns such as Grimsby and Kingston upon Hull. The survey and written quote are free.
What happens on a survey in Cleethorpes?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.