FD30 fire doors for Spalding buildings
If you need FD30 fire doors in Spalding, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
Fire doors in Spalding protect escape routes in small offices, schools and light industrial buildings alike. We adapt the programme to the building and its occupants, never the standard of the installation.
Each FD30 leaf we supply for Spalding is sized for the opening, rather than trimmed beyond what its certification allows. In Spalding, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
- Certified FD30 or FD30S leaf, or full doorset
- Fire-tested hinges, latch or lock and intumescent pads
Rules and responsibilities in Spalding
In Spalding, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Spalding building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD30 fire doors fit in Spalding
You are most likely to need FD30 fire doors if you look after shops, schools or care homes. Whatever the building in Spalding, we survey each opening and tell you which doors need work and which do not.
How a Spalding job runs
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Spalding?
Budget around £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. Our guide prices are the same in Spalding as elsewhere; what changes the cost is the doors themselves. Use our guide-price tool for a quick estimate.
Covering Spalding and nearby
Nearby towns we cover include Boston, Peterborough and Wisbech. Distance from Spalding does not change our guide prices, and the survey and quote are free.
Questions from Spalding
Do you work in Spalding?
Yes, we take on FD30 fire doors in Spalding and the surrounding area, including Boston and Peterborough. Send your postcode and a few details and we'll come back with survey dates.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.