FD60 fire doors: our service in Great Malvern
Our FD60 fire doors service in Great Malvern is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Buildings in and around Great Malvern range from care homes to schools and family homes after loft conversions. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
Before ordering FD60 doors for a Great Malvern building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer. For FD60 work in Great Malvern we generally fit certified doorsets, so frame and leaf share the same test evidence.
Why FD60 installation is less forgiving
A 54mm leaf can weigh considerably more than a 44mm one. That weight drives everything else: more robust frames and fixings, hinges rated for the load, and a closer with enough power to close and latch the door without making it too heavy to open. Glazing, if any, must use a 60-minute glass and glazing system from the same test evidence.
Because of this, most FD60 openings are best done as a certified doorset, so the frame and leaf come with matching evidence.
What you get:
- Check of the fire strategy rating for each opening
- 60-minute glazing systems where vision panels are needed
- Frame fixing and structural gap sealing recorded with photos
- Load-rated hinges and correctly powered closer
Rules and responsibilities in Great Malvern
In Great Malvern, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Great Malvern building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Which buildings in Great Malvern need FD60 fire doors?
You are most likely to need FD60 fire doors if you look after stair cores in taller blocks, mixed-use commercial buildings or refuse stores. Whatever the building in Great Malvern, we survey each opening and tell you which doors need work and which do not.
From enquiry to handover in Great Malvern
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Prices for FD60 fire doors in Great Malvern
Guide pricing for FD60 fire doors: £850–£1,800 per FD60 doorset supplied and fitted, ex VAT. Volume work across several doors in one Great Malvern building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Covering Great Malvern and nearby
Neighbouring towns such as Worcester, Tewkesbury, Droitwich and Stourport-on-Severn are covered too, so clients with several buildings can use one installer and one evidence format.
Questions from Great Malvern
Is Great Malvern within your coverage area?
It is. We cover Great Malvern in Worcestershire and neighbouring towns such as Worcester. There is no charge for the survey.
What happens on a survey in Great Malvern?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Are FD60 doors harder to open?
They are heavier, so the closer has to be chosen and adjusted with care. A well-set closer will still close and latch the door while keeping the opening force reasonable for the people who use it.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.