FD60 fire doors for Hereford buildings
Our FD60 fire doors service covers Hereford and the wider Herefordshire area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Around Hereford, schools, industrial estates and low-rise blocks of flats all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
Before ordering FD60 doors for a Hereford building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer. For FD60 work in Hereford we generally fit certified doorsets, so frame and leaf share the same test evidence.
Why FD60 installation is less forgiving
A 54mm leaf can weigh considerably more than a 44mm one. That weight drives everything else: more robust frames and fixings, hinges rated for the load, and a closer with enough power to close and latch the door without making it too heavy to open. Glazing, if any, must use a 60-minute glass and glazing system from the same test evidence.
Because of this, most FD60 openings are best done as a certified doorset, so the frame and leaf come with matching evidence.
As standard, the work covers:
- 60-minute glazing systems where vision panels are needed
- Intumescent and smoke seals as specified
- Load-rated hinges and correctly powered closer
- Check of the fire strategy rating for each opening
The regulations behind fire doors in Hereford
In Hereford, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Hereford building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD60 fire doors fit in Hereford
Landlords, managing agents, facilities teams and homeowners in Hereford can all commission FD60 fire doors from us. The usual settings are plant and boiler rooms and mixed-use commercial buildings, though single doors for refuse stores are just as welcome.
What happens after you enquire
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
What does FD60 fire doors cost in Hereford?
If you need a budget figure first, the guide for FD60 fire doors is £850–£1,800 per FD60 doorset supplied and fitted, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Covering Hereford and nearby
As well as Hereford, we cover neighbouring towns including Great Malvern, Worcester and Tewkesbury. The survey and quote are free.
Questions
Is Hereford within your coverage area?
It is. We cover Hereford in Herefordshire and neighbouring towns such as Great Malvern. There is no charge for the survey.
What happens on a survey in Hereford?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.
Are FD60 doors harder to open?
They are heavier, so the closer has to be chosen and adjusted with care. A well-set closer will still close and latch the door while keeping the opening force reasonable for the people who use it.