FD60 fire doors: our service in Swinton
Our FD60 fire doors service covers Swinton and the wider Greater Manchester area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Buildings in and around Swinton range from schools to family homes after loft conversions and light industrial buildings. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
FD60 openings in Swinton buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. Before ordering FD60 doors for a Swinton building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer.
What do you hand over at the end?
For every FD60 opening we record the product and certificate reference, the gap measurements, the hinge and closer specification, how the frame was fixed and what was used to seal the frame-to-structure gap, with photographs before the architraves go on. That record is what your fire risk assessor or building control officer will ask for.
On a typical job that means:
- 60-minute glazing systems where vision panels are needed
- Certified FD60 doorset or leaf with matching evidence
- Intumescent and smoke seals as specified
- Load-rated hinges and correctly powered closer
The regulations behind fire doors in Swinton
In Swinton, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Swinton building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Where FD60 fire doors fit in Swinton
Typical settings for FD60 fire doors include plant and boiler rooms, mixed-use commercial buildings and refuse stores. In Swinton, as anywhere, the duty holder varies: a responsible person for a workplace, a landlord or managing agent for a block or HMO, or a homeowner after building work. We adjust access, timing and paperwork to suit whoever commissions the work.
The steps on a Swinton installation
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Budgeting for FD60 fire doors in Swinton
As a guide, budget £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. The figure for your Swinton building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Around Swinton
Swinton is about 7.7 km from Manchester, and we cover both, along with nearby Eccles and Walkden. Send us your postcode and we'll confirm survey dates.
Common questions
Do you cover M27 and nearby postcodes?
Yes. We cover Swinton including M27, and nearby towns such as Eccles and Walkden. The survey and written quote are free.
How quickly can you survey in Swinton?
It depends on the number of doors and access, but we offer survey dates as soon as we reply to your enquiry. If an inspection has found urgent safety issues, tell us and we'll prioritise.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.
Are FD60 doors harder to open?
They are heavier, so the closer has to be chosen and adjusted with care. A well-set closer will still close and latch the door while keeping the opening force reasonable for the people who use it.