FD30 fire doors for Sunderland buildings
Our FD30 fire doors service in Sunderland is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Fire doors in Sunderland protect escape routes in offices, GP surgeries and purpose-built flats alike. We adapt the programme to the building and its occupants, never the standard of the installation.
In Sunderland, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. Each FD30 leaf we supply for Sunderland is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Survey of the opening, frame and existing ironmongery
- Overhead closer set to close and latch
- Certified FD30 or FD30S leaf, or full doorset
- Fire-tested hinges, latch or lock and intumescent pads
The regulations behind fire doors in Sunderland
The rules that apply to fire doors in Sunderland are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Sunderland block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Where FD30 fire doors fit in Sunderland
Landlords, managing agents, facilities teams and homeowners in Sunderland can all commission FD30 fire doors from us. The usual settings are shops and HMOs, though single doors for blocks of flats are just as welcome.
What happens after you enquire
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Sunderland?
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Covering Sunderland and nearby
Neighbouring towns such as Seaham, Washington, Houghton-Le-Spring and Jarrow are covered too, so clients with several buildings can use one installer and one evidence format.
Common questions
Do you work in Sunderland?
Yes, we take on FD30 fire doors in Sunderland and the surrounding area, including Seaham and Washington. Send your postcode and a few details and we'll come back with survey dates.
Can you work from an existing inspection report for my Sunderland building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.