Getting FD30 fire doors right in Harrogate
Our FD30 fire doors service in Harrogate is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Fire doors in Harrogate protect escape routes in family homes after loft conversions, low-rise blocks of flats and high-street shops alike. We adapt the programme to the building and its occupants, never the standard of the installation.
Each FD30 leaf we supply for Harrogate is sized for the opening, rather than trimmed beyond what its certification allows. In Harrogate, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
As standard, the work covers:
- Photo record, product data and certificate references at handover
- Overhead closer set to close and latch
- Intumescent strips and smoke seals to the certification
- Survey of the opening, frame and existing ironmongery
Rules and responsibilities in Harrogate
The rules that apply to fire doors in Harrogate are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Harrogate block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Buildings and duty holders in Harrogate
The need for FD30 fire doors usually arises in care homes or offices, and sometimes HMOs. Each has its own pressures, such as residents at home or a building that must stay open, so we plan the sequence of work in Harrogate to keep escape routes protected throughout.
How a Harrogate job runs
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Prices for FD30 fire doors in Harrogate
Guide pricing for FD30 fire doors: £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. Volume work across several doors in one Harrogate building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Nearby areas we cover from Harrogate
We also cover towns near Harrogate, including Yeadon (17.2 km away), Guiseley and Leeds. If your building is in HG2 or a neighbouring district, the service and pricing are the same.
Common questions
Is Harrogate within your coverage area?
It is. We cover Harrogate in North Yorkshire and neighbouring towns such as Yeadon. There is no charge for the survey.
Can you work from an existing inspection report for my Harrogate building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.