What FD30 fire doors in Winchester should include
From the SO23 postcode district outwards, we take on FD30 fire doors across Winchester for homes, blocks and workplaces.
Around Winchester, small blocks of flats, schools and family homes after loft conversions all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
In Winchester, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. For a mixed portfolio in Winchester, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
Each installation includes:
- Certified FD30 or FD30S leaf, or full doorset
- Frame-to-wall gap sealed with an evidenced material
- Photo record, product data and certificate references at handover
- Overhead closer set to close and latch
Which fire door rules apply in Winchester?
In Winchester, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Winchester building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Which buildings in Winchester need FD30 fire doors?
Landlords, managing agents, facilities teams and homeowners in Winchester can all commission FD30 fire doors from us. The usual settings are schools and care homes, though single doors for blocks of flats are just as welcome.
Our process in Winchester
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Budgeting for FD30 fire doors in Winchester
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Winchester
Neighbouring towns such as Eastleigh, Southampton, Totton and Andover are covered too, so clients with several buildings can use one installer and one evidence format.
Questions
Do you work in Winchester?
Yes, we take on FD30 fire doors in Winchester and the surrounding area, including Eastleigh and Southampton. Send your postcode and a few details and we'll come back with survey dates.
Can you work from an existing inspection report for my Winchester building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.