FD60 fire doors in Falkirk, done to the evidence
We provide FD60 fire doors in Falkirk (FK1 and the surrounding postcodes), from the first survey through to a documented handover.
Buildings in and around Falkirk range from care homes to small offices and light industrial buildings. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
Before ordering FD60 doors for a Falkirk building, we check the rating each opening actually needs, because over-specifying makes doors heavier and dearer. For FD60 work in Falkirk we generally fit certified doorsets, so frame and leaf share the same test evidence.
When does a building need FD60 rather than FD30?
FD60 doors appear where the fire strategy asks a wall to resist fire for an hour: stair cores and lobbies in taller buildings, plant and boiler rooms, some service risers, refuse stores and compartment walls between different uses. The rating follows the wall. Fitting an FD30 door in a 60-minute wall leaves a weak point, and fitting FD60 everywhere wastes money and makes doors harder to open.
We work from your fire strategy, the building's drawings or the fire risk assessment. Where these disagree with what is on site, we flag it before ordering.
As standard, the work covers:
- 60-minute glazing systems where vision panels are needed
- Load-rated hinges and correctly powered closer
- Intumescent and smoke seals as specified
- Certified FD60 doorset or leaf with matching evidence
Rules and responsibilities in Falkirk
In Falkirk, fire doors are specified against Scotland's Technical Handbooks (Section 2: Fire) under the Building (Scotland) Regulations 2004, rather than Approved Document B. Duties in non-domestic premises come from the Fire (Scotland) Act 2005 and the Fire Safety (Scotland) Regulations 2006.
England's regulation 10 does not apply in Scotland. We follow the building's fire risk assessment and, where building work needs a warrant, the local authority's requirements.
Who needs FD60 fire doors in Falkirk?
From plant and boiler rooms to refuse stores, the requirement for FD60 fire doors in Falkirk comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
From enquiry to handover in Falkirk
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
What does FD60 fire doors cost in Falkirk?
Guide pricing for FD60 fire doors: £850–£1,800 per FD60 doorset supplied and fitted, ex VAT. Volume work across several doors in one Falkirk building usually brings the per-door cost down. Your written quote is fixed once we have surveyed.
Nearby areas we cover from Falkirk
We also cover towns near Falkirk, including Alloa (12.7 km away), Cumbernauld and Bathgate. If your building is in FK1 or a neighbouring district, the service and pricing are the same.
Common questions
Do you cover FK1 and nearby postcodes?
Yes. We cover Falkirk including FK1, and nearby towns such as Alloa and Cumbernauld. The survey and written quote are free.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.