What FD30 fire doors in Rotherham should include
Our FD30 fire doors service covers Rotherham and the wider South Yorkshire area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Rotherham has a broad mix of buildings, including HMOs, offices and purpose-built flats, and the same fire door principles apply to all of them.
In Rotherham, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. For a mixed portfolio in Rotherham, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Frame-to-wall gap sealed with an evidenced material
- Intumescent strips and smoke seals to the certification
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
Fire door law for Rotherham properties
In Rotherham, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Rotherham building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Who needs FD30 fire doors in Rotherham?
Typical settings for FD30 fire doors include offices, shops and HMOs. In Rotherham, as anywhere, the duty holder varies: a responsible person for a workplace, a landlord or managing agent for a block or HMO, or a homeowner after building work. We adjust access, timing and paperwork to suit whoever commissions the work.
The steps on a Rotherham installation
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
What does FD30 fire doors cost in Rotherham?
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Rotherham
Rotherham is about 8.9 km from Sheffield, and we cover both, along with nearby Burngreave and Chapeltown. Send us your postcode and we'll confirm survey dates.
Questions
Is Rotherham within your coverage area?
It is. We cover Rotherham in South Yorkshire and neighbouring towns such as Burngreave. There is no charge for the survey.
Do I need to be there for the survey?
Someone needs to give us access to the doors. For blocks and commercial buildings, a caretaker or site contact is fine; for HMOs and homes, we agree a time with you or your tenants.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.