What FD30 fire doors in Huntingdon should include
For property owners, landlords and managing agents in Huntingdon, we offer FD30 fire doors with one team for the survey, the product and the installation.
Around Huntingdon, houses with integral garages, small offices and small blocks of flats all depend on fire doors that close, latch and seal. We survey each opening and tell you plainly which doors need work and which don't.
For a mixed portfolio in Huntingdon, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side. Each FD30 leaf we supply for Huntingdon is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
What you get:
- Overhead closer set to close and latch
- Intumescent strips and smoke seals to the certification
- Photo record, product data and certificate references at handover
- Frame-to-wall gap sealed with an evidenced material
What the rules say for Huntingdon
In Huntingdon, as elsewhere in England, the starting point is the Fire Safety Order 2005: whoever controls a workplace or the shared parts of a residential block must make sure its fire doors work. When doors are replaced, the Building Regulations and Approved Document B set the standard the new work has to meet.
Blocks above 11 metres have a specific routine under regulation 10 of the Fire Safety (England) Regulations 2022: quarterly checks of communal fire doors and annual best-endeavours checks of flat front doors. If your Huntingdon building is a higher-risk building under the Building Safety Act 2022, we confirm the approval route with the Principal Accountable Person before any work is ordered.
Which buildings in Huntingdon need FD30 fire doors?
From blocks of flats to care homes, the requirement for FD30 fire doors in Huntingdon comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
What happens after you enquire
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Budgeting for FD30 fire doors in Huntingdon
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Huntingdon
Neighbouring towns such as St Neots, Cambridge, Peterborough and Rushden are covered too, so clients with several buildings can use one installer and one evidence format.
Questions from Huntingdon
Do you cover PE29 and nearby postcodes?
Yes. We cover Huntingdon including PE29, and nearby towns such as St Neots and Cambridge. The survey and written quote are free.
What happens on a survey in Huntingdon?
We look at every door in scope: the leaf, frame, gaps, seals, hinges, closer, glazing and how the frame is fixed. You then get a written quote that prices each door separately.
Do FD30 doors need a closer?
Most do. Doors on escape routes, flat entrance doors and doors in the common parts of buildings need a self-closing device that shuts and latches the door. Some doors inside houses and locked riser doors are exceptions, depending on the fire strategy.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.