FD30 fire doors in Amersham, done to the evidence
Our FD30 fire doors service in Amersham is simple: a survey, a fixed quote, certified products and an installation finished to the manufacturer's evidence.
Fire doors in Amersham protect escape routes in light industrial buildings, small offices and houses with integral garages alike. We adapt the programme to the building and its occupants, never the standard of the installation.
For a mixed portfolio in Amersham, we can survey every FD30 opening in one visit and price leaf-only and doorset options side by side. Each FD30 leaf we supply for Amersham is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
As standard, the work covers:
- Overhead closer set to close and latch
- Frame-to-wall gap sealed with an evidenced material
- Intumescent strips and smoke seals to the certification
- Photo record, product data and certificate references at handover
The regulations behind fire doors in Amersham
The rules that apply to fire doors in Amersham are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Amersham block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Who needs FD30 fire doors in Amersham?
You are most likely to need FD30 fire doors if you look after offices, blocks of flats or schools. Whatever the building in Amersham, we survey each opening and tell you which doors need work and which do not.
From enquiry to handover in Amersham
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Prices for FD30 fire doors in Amersham
As a guide, budget £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT for FD30 fire doors. The figure for your Amersham building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Covering Amersham and nearby
Neighbouring towns such as Chesham, Chalfont St Peter, Gerrards Cross and High Wycombe are covered too, so clients with several buildings can use one installer and one evidence format.
Questions from Amersham
Do you work in Amersham?
Yes, we take on FD30 fire doors in Amersham and the surrounding area, including Chesham and Chalfont St Peter. Send your postcode and a few details and we'll come back with survey dates.
How quickly can you survey in Amersham?
It depends on the number of doors and access, but we offer survey dates as soon as we reply to your enquiry. If an inspection has found urgent safety issues, tell us and we'll prioritise.
Can a new FD30 door go into my old frame?
Sometimes. The frame has to be sound, square, securely fixed and compatible with the new leaf's certification. Many older frames are not, especially softwood linings or frames altered for previous doors. We check each frame on the survey and recommend a doorset only where the frame cannot be relied on.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.