FD60 fire doors for Bentley buildings
Our FD60 fire doors service covers Bentley and the wider South Yorkshire area. Every job starts with a survey of the openings, so the quote reflects your actual doors rather than a guess.
Buildings in and around Bentley range from care homes to small blocks of flats and small offices. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
FD60 openings in Bentley buildings tend to be stair cores, plant rooms and bin stores in larger blocks and commercial premises. For FD60 work in Bentley we generally fit certified doorsets, so frame and leaf share the same test evidence.
Why FD60 installation is less forgiving
A 54mm leaf can weigh considerably more than a 44mm one. That weight drives everything else: more robust frames and fixings, hinges rated for the load, and a closer with enough power to close and latch the door without making it too heavy to open. Glazing, if any, must use a 60-minute glass and glazing system from the same test evidence.
Because of this, most FD60 openings are best done as a certified doorset, so the frame and leaf come with matching evidence.
As standard, the work covers:
- Check of the fire strategy rating for each opening
- Load-rated hinges and correctly powered closer
- Intumescent and smoke seals as specified
- Certified FD60 doorset or leaf with matching evidence
Which fire door rules apply in Bentley?
The rules that apply to fire doors in Bentley are England's. The responsible person under the Regulatory Reform (Fire Safety) Order 2005 must keep fire doors in non-domestic premises and the common parts of flats in working order; the Fire Safety Act 2021 confirmed that this includes flat entrance doors onto common parts.
Where a Bentley block is above 11 metres, regulation 10 of the 2022 regulations means communal doors are checked every three months and flat entrance doors annually on a best-endeavours basis. Replacement doors must also satisfy the Building Regulations, with Approved Document B as the guidance most building control bodies work from.
Where FD60 fire doors fit in Bentley
Landlords, managing agents, facilities teams and homeowners in Bentley can all commission FD60 fire doors from us. The usual settings are plant and boiler rooms and refuse stores, though single doors for stair cores in taller blocks are just as welcome.
How a Bentley job runs
- Confirm the 60-minute requirement against the fire strategy
- Survey structure, opening size and wall type
- Order the certified doorset with ironmongery to its evidence
- Install the frame, fix and seal it to the structure
- Hang, adjust and test the leaf, closer and latching
- Record evidence and make good
Budgeting for FD60 fire doors in Bentley
As a guide, budget £850–£1,800 per FD60 doorset supplied and fitted, ex VAT for FD60 fire doors. The figure for your Bentley building depends on the number of doors, the rating, the condition of the frames, finishes, hardware and access. We confirm a fixed price after the free survey.
Bentley and neighbouring towns
Nearby towns we cover include Doncaster, Rotherham and Pontefract. Distance from Bentley does not change our guide prices, and the survey and quote are free.
Questions
Is Bentley within your coverage area?
It is. We cover Bentley in South Yorkshire and neighbouring towns such as Doncaster. There is no charge for the survey.
Can you work from an existing inspection report for my Bentley building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
Is FD60 just a thicker FD30?
No. FD60 doors are built and tested as a different product, usually with a thicker core, different seals and different ironmongery. Only the tested combination carries the 60-minute rating.
Can I upgrade an FD30 door to FD60?
Not by adding parts. An FD30 leaf cannot be turned into an FD60 door with extra strips or paint. If an opening needs 60 minutes, the leaf, and usually the frame, need to be replaced with a certified FD60 product.