What FD30 fire doors in Camborne should include
If you need FD30 fire doors in Camborne, we can survey, supply and install, then leave you the evidence your fire risk assessor will ask for.
Buildings in and around Camborne range from light industrial buildings to small offices and care homes. Whatever the building, the standard is the same: certified products, correct gaps, seals and closers, and a frame sealed to the wall.
In Camborne, FD30 doors are the usual choice for escape-route corridors, stairs and kitchen doors where the fire strategy asks for 30 minutes. Each FD30 leaf we supply for Camborne is sized for the opening, rather than trimmed beyond what its certification allows.
What does a correct FD30 installation include?
A typical timber FD30 leaf is around 44mm thick and hangs on at least three fire-tested hinges. The gaps between leaf and frame are set to the manufacturer's data, usually around 3mm. Intumescent strips, and smoke seals where needed, go in the frame or leaf edge as specified. The closer must pull the door shut and latch it from any angle. Every hole cut for a lock, latch or hinge is lined with intumescent material where the certification calls for it.
Then comes the part that is often skipped: sealing the gap between the frame and the wall with a tested material, as BS 8214:2026 now sets out in more detail.
On a typical job that means:
- Frame-to-wall gap sealed with an evidenced material
- Intumescent strips and smoke seals to the certification
- Survey of the opening, frame and existing ironmongery
- Photo record, product data and certificate references at handover
The regulations behind fire doors in Camborne
Fire doors in Camborne fall under English rules. New and replacement doors are covered by the Building Regulations 2010 and Approved Document B. In workplaces and the common parts of blocks, the Regulatory Reform (Fire Safety) Order 2005, as clarified by the Fire Safety Act 2021, puts the duty on the responsible person to keep fire doors suitable and maintained.
For residential buildings in Camborne above 11 metres, regulation 10 of the Fire Safety (England) Regulations 2022 adds checks: communal fire doors at least every three months and best-endeavours checks of flat entrance doors at least every twelve months. Higher-risk buildings of at least 18 metres or seven storeys also come under the Building Safety Act 2022, where works may need approval from the Building Safety Regulator.
Who needs FD30 fire doors in Camborne?
From HMOs to blocks of flats, the requirement for FD30 fire doors in Camborne comes from the fire strategy or risk assessment for the building. We work from that document, or help you interpret your inspection report, before quoting.
How a Camborne job runs
- Measure the opening, check the frame and confirm the rating needed
- Order a certified leaf or doorset to size, with matching components
- Remove the old door and assess the frame or structural opening
- Fix the frame and hang the leaf to the certified gap tolerances
- Fit seals, hinges, latch, closer and signage, then test close-and-latch
- Seal the frame-to-wall gap, make good and record the evidence
Guide prices in Camborne
If you need a budget figure first, the guide for FD30 fire doors is £300–£600 for a leaf into a sound existing frame; £650–£1,300 for a doorset, ex VAT. We firm that up after a survey, pricing each door separately so you can see where the money goes.
Nearby areas we cover from Camborne
Camborne is about 5.7 km from Redruth, and we cover both, along with nearby Falmouth and Truro. Send us your postcode and we'll confirm survey dates.
Questions
Do you cover TR14 and nearby postcodes?
Yes. We cover Camborne including TR14, and nearby towns such as Redruth and Falmouth. The survey and written quote are free.
Can you work from an existing inspection report for my Camborne building?
Yes. Send it over and we can often price straight from it, then confirm on site. We report back against the same door references so you can close actions off.
What is the difference between FD30 and FD30S?
FD30S has been tested for smoke control as well as fire. It adds a smoke seal, usually a brush or blade, and needs a tight threshold gap. Flat entrance doors and doors onto protected escape routes are commonly specified as FD30S.
How long does it take to fit an FD30 door?
A leaf into a sound frame is often a few hours. A full doorset including frame removal, fixing, sealing and making good is usually half a day to a day per opening, depending on access and the wall construction.